What is polycarbonate roofing? It’s a lightweight, transparent or translucent plastic roofing panel made from polycarbonate, a tough thermoplastic that lets daylight through while standing up to impacts far better than glass or acrylic. It’s sold as corrugated sheets, flat solid sheets and hollow “multiwall” sheets, and it’s most often used on patio covers, pergolas, greenhouses, carports, sheds and skylights rather than as the main roof over a house.
Good polycarbonate panels have a UV-protective layer on the outside face to prevent yellowing and brittleness. Choosing the right type comes down to how much light you want, how much insulation you need, and how much snow and wind the structure has to carry.
In this article
- What Polycarbonate Roofing Is Made Of
- Types of Polycarbonate Roofing Panels
- Why the UV Coating Matters
- Common Uses for Polycarbonate Roofing
- Pros and Cons of Polycarbonate Roofing
- Polycarbonate vs. PVC vs. Acrylic Panels
- Snow Load Considerations
- Installation Basics and Safety
- Care, Cleaning and Lifespan
- Frequently Asked Questions
What Polycarbonate Roofing Is Made Of
Polycarbonate is a clear engineering plastic. In roofing, it’s extruded into panels that can be glass-clear, tinted, opal (milky white) or solar-reflective. The appeal is simple: it brings in natural light like glass, but weighs far less and is much harder to break.
Raw polycarbonate doesn’t hold up well to sunlight on its own. Outdoor-grade roofing panels have a UV-protective layer co-extruded onto the surface, which is what keeps them from yellowing and turning brittle. Manufacturers such as Palram make panels with the UV layer on one side (to face the sky) or on both sides for applications where both faces get sun.
Types of Polycarbonate Roofing Panels
There are three main forms. They’re all made from the same plastic, but they behave very differently on a roof.
Corrugated polycarbonate panels
Corrugated panels are single-layer sheets formed into a wave or trapezoid profile, much like corrugated metal. The profile gives them stiffness so they can span between purlins (horizontal supports). They’re the most common choice for DIY patio covers, carports, sheds and greenhouses, and they’re widely stocked at home centers.
Clear corrugated panels let in a lot of light. Palram rates its clear Suntuf panels at 90% light transmission, with tinted options much lower (opal white 45%, solar gray 35%). Tuftex lists 93% for its clear PolyCarb panels. Because they’re a single layer, they offer very little insulation.
Multiwall (twinwall and triplewall) panels
Multiwall polycarbonate is a hollow sheet with two or more flat layers connected by internal ribs, a bit like corrugated cardboard. The trapped air makes it a far better insulator than single-layer sheets, and the ribs make it stiff for its weight. It’s the go-to material for greenhouses, sunrooms, pool enclosures and skylights.
Palram’s Sunlite line shows the range available:
| Structure | Thicknesses | Light transmission (clear) | U-value (lower = better insulation) |
|---|---|---|---|
| Twinwall | 4 to 10 mm | 82% (4 mm) to 79% (10 mm) | 3.8 (4 mm) to 2.9 (10 mm) W/m²K |
| Triplewall | 8 to 16 mm | 76% | 3.0 (8 mm) to 2.3 (16 mm) W/m²K |
| Thick multi-cell (X-Lite) | 16 to 35 mm | 60% to 57% | 2.1 (16 mm) to 1.5 (35 mm) W/m²K |
The trade-off is clear in the numbers: thicker, more complex sheets insulate better but let through less light. They also diffuse light rather than leaving it glass-clear, which many gardeners prefer because it softens harsh direct sun.
Solid polycarbonate sheets
Solid sheets are flat, single-thickness panels with no hollow cells. They look the most like glass, offer the clearest view and are extremely tough, which is why they’re used for skylights, canopies, security glazing and walkway covers. They’re heavier and more expensive per square foot than multiwall, and a solid sheet insulates far less than a multiwall sheet of similar weight.
| Panel type | Best for | Clarity | Insulation | Typical buyer |
|---|---|---|---|---|
| Corrugated | Patio covers, carports, sheds, simple greenhouses | High, clear or tinted | Very low | DIYers and budget projects |
| Multiwall | Greenhouses, sunrooms, pool enclosures, skylights | Diffused | Moderate to good | Projects where heat retention matters |
| Solid | Skylights, canopies, glazing, entry covers | Glass-like | Low | Projects that want a clear view and maximum toughness |
Why the UV Coating Matters
The UV layer is the single most important quality feature in polycarbonate roofing. Without it, sunlight degrades the plastic, causing yellowing, haze and eventually brittleness. With it, panels can stay clear and tough for many years. Palram, for example, offers a limited warranty, described as lifetime, against Suntuf panels losing more than 10% of their light transmission, and a 10-year warranty against impact damage, including hail.
Two practical points follow from this:
- Install the UV side up. Panels are labeled or have a printed film on the protected side. Palram warns that a panel installed upside down will discolor.
- Remove the protective film promptly. On multiwall sheets, Palram notes that sun exposure can fuse the masking film to the sheet if it’s left on too long after installation.
Cheap, unbranded panels sometimes have thin or no UV protection. If a product doesn’t clearly state its UV protection and warranty, treat that as a warning sign.
Common Uses for Polycarbonate Roofing
Patio covers and pergolas
Polycarbonate is a popular way to keep rain off a deck or patio without making the space underneath dark. Tinted or solar-control panels reduce glare and heat. Tuftex recommends a light-colored, well-ventilated support structure, since heat trapped between dark framing and the panels can damage them.
Greenhouses
Multiwall polycarbonate is a favorite for greenhouses because it insulates better than single glass, diffuses light evenly, and survives hail and stray baseballs. Twinwall is common on hobby greenhouses; thicker triplewall or multi-cell sheets suit colder climates where heat retention matters more.
Carports, sheds and outbuildings
Corrugated panels are often used alone or mixed with metal panels as skylights on sheds, barns and carports. Some corrugated profiles are made to line up with common metal roofing profiles, so a few clear panels can be swapped in to add daylight.
Skylights, canopies and walkway covers
Solid and multiwall sheets are used for skylights, door canopies, bus shelters and covered walkways where a clear, impact-resistant surface matters.
Is polycarbonate used on house roofs?
Rarely as the main roof over living space. Polycarbonate panels don’t provide the insulation, fire performance or long-term weatherproofing that homeowners expect from shingles, metal or membrane roofing over a heated home, and building codes treat light-transmitting plastics differently from standard roof coverings. For a home’s primary roof, look at conventional roofing materials and professional roof installation.
Pros and Cons of Polycarbonate Roofing
Advantages
- Natural light: Clear panels let through most visible light, and tinted or opal options let you control glare and heat.
- Impact resistance: Polycarbonate is far tougher than glass or acrylic, which is why manufacturers like Palram back their panels against hail damage.
- Light weight: Panels are easy to carry and cut, and need lighter framing than glass.
- Wide temperature range: Palram lists a long-term service range of -50°C to +100°C (about -58°F to 212°F) for Sunlite multiwall, and Tuftex rates its PolyCarb panels for surface temperatures down to -40°F.
- Insulation (multiwall): Hollow-cell sheets insulate far better than single-layer glazing.
- DIY-friendly: Corrugated panels can be installed with basic tools on a simple frame, following the manufacturer’s instructions.
Disadvantages
- Scratches easily: Polycarbonate is softer than acrylic or glass. Abrasive cleaning tools will haze the surface.
- Thermal expansion: It expands and contracts noticeably with temperature. Palram puts the practical movement at about 3 mm per meter (roughly 1/8 inch per 39 inches) over a 50°C swing. Fastener holes must be oversized to allow for it, or the panels can buckle.
- Chemical sensitivity: Some sealants, adhesives, paints and cleaners attack polycarbonate. Palram specifically warns against ammonia-based glass cleaners.
- Heat under clear panels: Clear panels can make the space below hot in summer. Tinted or solar-control panels help.
- Noise: Single-layer corrugated panels can be loud in heavy rain or hail.
- Not walkable: Panels can’t support foot traffic between supports, which makes cleaning and snow removal harder.
- Cost of quality: Well-made, UV-protected panels cost more than PVC panels, and multiwall or solid sheets cost more again.
Polycarbonate vs. PVC vs. Acrylic Panels
Next to polycarbonate on the store shelf, you’ll usually find PVC (vinyl) corrugated panels and, for flat sheets, acrylic. They can look almost identical, but they perform differently.
| Feature | Polycarbonate | PVC (vinyl) | Acrylic |
|---|---|---|---|
| Impact resistance | Highest; resists hail and impacts | Lower than polycarbonate | Much lower than polycarbonate; more brittle, especially when flexed in cold |
| Temperature tolerance | Wide; Tuftex rates PolyCarb to -40°F | Narrower; Tuftex limits opaque vinyl to 150°F surface temperature and translucent/clear vinyl to 125°F | Lower heat tolerance than polycarbonate |
| Support spacing (Tuftex corrugated) | Up to 36 inches on center | Maximum 24 inches on center | Not typically sold as corrugated roofing |
| Load rating (Tuftex, on 24-inch centers) | 115 psf | 90 psf | — |
| UV resistance | Good with a UV-protected surface | Translucent and clear vinyl not recommended for high UV exposure | Naturally UV resistant |
| Clarity | High | Varies by product | Highest; can be polished to restore clarity |
| Scratch resistance | Low | Varies by product | Better than polycarbonate |
| Cost | Higher | Lowest | Usually less than polycarbonate for flat sheet |
In short, PVC panels are a budget option for small, sheltered projects in mild conditions. Acrylic is clearer and more scratch-resistant but much more brittle. Polycarbonate costs more, but it’s the better choice anywhere hail, temperature swings or heavier loads are a concern.
Snow Load Considerations
Snow is where many polycarbonate projects fail, usually because the supports are too far apart rather than because the panels themselves are weak. The panel’s load capacity depends heavily on how closely it’s supported.
Follow the manufacturer’s span charts
Manufacturers publish tables that match support spacing to the load the roof must carry. Palram’s Suntuf installation guide, for example, lists these maximum purlin spacings for its corrugated panels:
| Design load | Maximum purlin spacing (Suntuf) |
|---|---|
| 20 psf | 36 inches |
| 30 psf | 30 inches |
| 40 psf | 24 inches |
| 50 psf | 16 inches |
Tuftex lists a 115 psf rating for its PolyCarb panels on 24-inch centers and allows up to 36 inches on center. Ratings differ by brand, profile and thickness, so use the chart for the exact product you’re buying. For multiwall sheets, Palram’s span tables vary by thickness and by whether the sheet is supported on two or four sides, and edge spans are shorter than middle spans.
Code loads come first
Palram’s guides state that local building codes and engineering design take precedence over their tables. In snowy regions, those code loads can be substantial. Minnesota’s building code, for example, sets ground snow loads of 50 or 60 pounds per square foot depending on the county, and roof design loads are calculated from there. An attached patio cover or carport may also need a permit, so check with your local building department before you build.
Wet snow is much heavier than fresh snow
Palram’s multiwall guide notes that fresh, fluffy snow weighs roughly 0.8 to 1.9 kg/m² per centimeter of depth, while wet, compacted snow weighs 2.0 to 8.0 kg/m² per centimeter. Per inch of depth, that’s roughly 0.4 to 1 psf for fresh snow and 1 to 4 psf for wet snow, so a spring storm can load a roof far more than the same depth of powder.
Slope helps snow and water shed
Palram recommends a minimum slope of 1.5 inches per 12 inches for Suntuf corrugated panels, and at least 5% (10% preferred) for multiwall sheets. Tuftex calls for at least 1 inch per foot and up to 3 inches per foot in heavy snow areas. Steeper is generally better for shedding snow and avoiding leaks at laps.
Never climb onto polycarbonate panels to clear snow. Palram warns against stepping on panels between supports. Use a long-handled roof rake from the ground, and if heavy accumulations are a regular problem, rethink the support spacing or slope.
Installation Basics and Safety
This isn’t a full how-to, and every brand has its own instructions, but these points show up across manufacturers’ guides:
- Use the manufacturer’s fasteners. Palram specifies its own EPDM-washered screws and warns against impact drivers; overtightening deforms the washer and can crack the panel.
- Pre-drill oversized holes. Palram calls for a 1/4-inch bit for its Suntuf fasteners, and Tuftex for 5/16-inch holes for its fasteners, so the panels can expand and contract.
- Fasten through the crowns on roofs. For Suntuf, fasten every other rib, or every rib in high-wind areas.
- Overlap correctly. Follow the specified side and end laps, and lay panels in the direction the guide recommends relative to the prevailing wind.
- Run multiwall flutes downhill so condensation can drain, seal the top edge with solid tape and the bottom edge with vented tape, then cover the ends with U-profiles or end caps.
- Respect the bending radius. Multiwall sheets can be cold-curved, but only to the manufacturer’s minimum radius. Palram lists 700 mm (about 27.5 inches) for its 4 mm twinwall, with larger radii for thicker sheets.
- Check sealant compatibility with the sealant maker before using it on polycarbonate.
Safety comes first on any roof project. Work from a stable ladder or scaffold, use fall protection when working at height, and never put your weight on panels between supports. Palram recommends a sturdy board that spans at least three structural members if you must reach across. Check whether your project needs a permit, and follow the manufacturer’s installation instructions so you don’t void the warranty. For more general guidance on planning a project, see our DIY roofing guide.
Care, Cleaning and Lifespan
Polycarbonate needs little maintenance, but the wrong cleaning method can ruin it.
- Clean with lukewarm, mildly soapy water and a soft cloth or sponge, then rinse. Palram warns against abrasive brushes and ammonia-based cleaners.
- Keep gutters and laps free of leaves so water drains and dirt doesn’t build up in corrugations.
- Check fasteners once a year. Loose screws or cracked washers can lead to leaks; replace them with the manufacturer’s fasteners.
- Inspect multiwall end tapes. If they fail, dirt, insects and algae can get into the cells.
Lifespan depends heavily on UV protection, installation quality and climate. A useful guide is the warranty: major brands such as Palram back multiwall sheets with a 10-year limited warranty, and Suntuf corrugated panels with a 10-year impact warranty plus a long-term light transmission warranty. Panels without stated UV protection or a warranty may fail much sooner.
Frequently Asked Questions
Is polycarbonate roofing better than PVC?
For most outdoor roofs, yes. Polycarbonate handles impacts, hail and temperature extremes better than PVC and can span wider supports; Tuftex, for example, rates its polycarbonate panels at 115 psf versus 90 psf for its vinyl panels on 24-inch centers. PVC is cheaper and fine for small, sheltered projects in mild conditions.
Does polycarbonate roofing turn yellow?
Unprotected polycarbonate yellows and becomes brittle in sunlight, but quality roofing panels have a co-extruded UV layer that prevents this. The UV side must face up; installing a panel upside down can cause discoloration.
Can polycarbonate roofing handle snow?
It can, if the panels are supported at the spacing the manufacturer specifies for your design load and local code. Closer purlin spacing and a steeper slope increase the snow load a polycarbonate roof can carry.
Can you walk on polycarbonate roofing?
No. Polycarbonate panels aren’t designed to support a person between supports. Manufacturers recommend using a board that spans several structural members if you must reach across, and clearing snow from the ground with a roof rake.
Is twinwall or corrugated polycarbonate better for a greenhouse?
Twinwall or multiwall usually works better for greenhouses because the hollow cells insulate and diffuse light. Corrugated panels let in more direct light and cost less but hold very little heat.
How do you clean polycarbonate roof panels?
Use lukewarm, mildly soapy water with a soft cloth or sponge, then rinse. Avoid abrasive brushes, solvents and ammonia-based glass cleaners, which can scratch or damage the surface.
Polycarbonate is a smart choice when you want light and protection from the weather in the same panel, as long as you pick a UV-protected product and support it properly for snow. If you’re weighing it against corrugated steel for a carport or outbuilding, our metal roofing page explains what metal panels offer.

